FIND YOUR SOLUTION

SELECT SOURCE
All
OSHA Compliant
SELECT TRADE
Concrete & Masonry
SELECT APPLICATION
Concrete Cutting / Tuck-Pointing
SELECT CATEGORY
Angle Grinders
SELECT TOOL
GA5042C
SELECT VACUUM/MODEL
VC4210L
VC4710
XCV04Z
XCV13Z

4 Results Found

  • Tool
  • 大小
    • Extractor/Model

    CONCRETE & MASONRY/CONCRETE CUTTING / TUCK-POINTING

    Specified Exposure Control Methods:For each employee engaged in a task identified on Table 1, the employer shall fully and properly implement the engineering controls, work practices, and respiratory protection specified for the task on Table 1.

    Performance option:The employer shall assess the 8-hour Time-Weighted Average (TWA) exposure for each employee on the basis of any combination of air monitoring data or objective data sufficient to accurately characterize employee exposures to respirable crystalline silica.

    相关文件:

    • Objective Test Data for Concrete Drilling with XRH03Z, XRH04Z, XRH06Z, RH01, HR2475 and HR2811F (PDF)DOWNLOAD
    • Objective Test Data for Concrete Drilling with XRH011TX, XRH05Z, HR2641, HR2651 and HR2661 (PDF)DOWNLOAD
    • Objective Test Data for Concrete Surfacing/Grinding with VC4710, using GA7011C, GA7040S and GA9040S (PDF)DOWNLOAD

    Scheduled Self-Monitoring:If a control method is not listed on Table 1 and no objective data is available, OSHA requires employers implement a monitoring program to show that the employees have exposure levels below the PEL. The employer shall perform initial monitoring to assess the 8-hour TWA exposure for each employee on the basis of one or more personal breathing zone air samples that reflect the exposures of employees on each shift, for each job classification, in each work area.

    CONCRETE & MASONRY/CONCRETE CUTTING / TUCK-POINTING

    Specified Exposure Control Methods:For each employee engaged in a task identified on Table 1, the employer shall fully and properly implement the engineering controls, work practices, and respiratory protection specified for the task on Table 1.

    Performance option:The employer shall assess the 8-hour Time-Weighted Average (TWA) exposure for each employee on the basis of any combination of air monitoring data or objective data sufficient to accurately characterize employee exposures to respirable crystalline silica.

    相关文件:

    • Objective Test Data for Concrete Drilling with XRH03Z, XRH04Z, XRH06Z, RH01, HR2475 and HR2811F (PDF)DOWNLOAD
    • Objective Test Data for Concrete Drilling with XRH011TX, XRH05Z, HR2641, HR2651 and HR2661 (PDF)DOWNLOAD
    • Objective Test Data for Concrete Surfacing/Grinding with VC4710, using GA7011C, GA7040S and GA9040S (PDF)DOWNLOAD

    Scheduled Self-Monitoring:If a control method is not listed on Table 1 and no objective data is available, OSHA requires employers implement a monitoring program to show that the employees have exposure levels below the PEL. The employer shall perform initial monitoring to assess the 8-hour TWA exposure for each employee on the basis of one or more personal breathing zone air samples that reflect the exposures of employees on each shift, for each job classification, in each work area.

    CONCRETE & MASONRY/CONCRETE CUTTING / TUCK-POINTING

    Specified Exposure Control Methods:For each employee engaged in a task identified on Table 1, the employer shall fully and properly implement the engineering controls, work practices, and respiratory protection specified for the task on Table 1.

    Performance option:The employer shall assess the 8-hour Time-Weighted Average (TWA) exposure for each employee on the basis of any combination of air monitoring data or objective data sufficient to accurately characterize employee exposures to respirable crystalline silica.

    相关文件:

    • Objective Test Data for Concrete Drilling with XRH03Z, XRH04Z, XRH06Z, RH01, HR2475 and HR2811F (PDF)DOWNLOAD
    • Objective Test Data for Concrete Drilling with XRH011TX, XRH05Z, HR2641, HR2651 and HR2661 (PDF)DOWNLOAD
    • Objective Test Data for Concrete Surfacing/Grinding with VC4710, using GA7011C, GA7040S and GA9040S (PDF)DOWNLOAD

    Scheduled Self-Monitoring:If a control method is not listed on Table 1 and no objective data is available, OSHA requires employers implement a monitoring program to show that the employees have exposure levels below the PEL. The employer shall perform initial monitoring to assess the 8-hour TWA exposure for each employee on the basis of one or more personal breathing zone air samples that reflect the exposures of employees on each shift, for each job classification, in each work area.

    CONCRETE & MASONRY/CONCRETE CUTTING / TUCK-POINTING

    Specified Exposure Control Methods:For each employee engaged in a task identified on Table 1, the employer shall fully and properly implement the engineering controls, work practices, and respiratory protection specified for the task on Table 1.

    Performance option:The employer shall assess the 8-hour Time-Weighted Average (TWA) exposure for each employee on the basis of any combination of air monitoring data or objective data sufficient to accurately characterize employee exposures to respirable crystalline silica.

    相关文件:

    • Objective Test Data for Concrete Drilling with XRH03Z, XRH04Z, XRH06Z, RH01, HR2475 and HR2811F (PDF)DOWNLOAD
    • Objective Test Data for Concrete Drilling with XRH011TX, XRH05Z, HR2641, HR2651 and HR2661 (PDF)DOWNLOAD
    • Objective Test Data for Concrete Surfacing/Grinding with VC4710, using GA7011C, GA7040S and GA9040S (PDF)DOWNLOAD

    Scheduled Self-Monitoring:If a control method is not listed on Table 1 and no objective data is available, OSHA requires employers implement a monitoring program to show that the employees have exposure levels below the PEL. The employer shall perform initial monitoring to assess the 8-hour TWA exposure for each employee on the basis of one or more personal breathing zone air samples that reflect the exposures of employees on each shift, for each job classification, in each work area.

    For Dust Management solutions that are OSHA compliant under Option 2:Compliant under Option 2, Objective Data of the OSHA standard for Occupational Exposure to Respirable Crystalline Silica (rule 1926.1153) when dust extractor is operated with the tested tool model and operated under conditions tested by Makita®.

    Note: To ensure performance, verify that any engineer controls (accessory-components used with the dust collector/vacuum such as dust shrouds, dust extraction attachments, connectors) are used per manufacturer instructions, and are securely attached to a compliant vacuum.

    • Vacuums

    • Makita Dust Extractors

      Find the Makita®dust extraction vacuum that works for you.

    • AWS

    • AWS®AUTO-START WIRELESS SYSTEM

      Discover the Convenience of Intelligent Communication

    • OSHA

    • OSHA Compliance Rule 29 CFR 1926.1153

      Find out how to get your Makita tools and equipment compliant.

    • Product Search

    • MAKITA®DUST MANAGEMENT PRODUCT SEARCH

      Not sure which tools and accessories match up? Our dust management search tool can help.

    We use cookies to improve your experience on our site. To find out more, review ourprivacy policyunder "Web Browser Cookies"

    ACCEPT ALL COOKIES Learn More